Table of Contents
Laptops consist of a built-in antenna for wireless networks, but most also have a wifi plug to attach an external antenna. You can make your external wifi antenna that will give a better signal to the laptop. It requires some household items along with some parts of an electronics store or hardware. The antenna you construct will better meet the laptop’s wireless requirements without opening the laptop or canceling its warranty. In this article, we will tell you how to make a wifi antenna for laptop.
Read More: 10 Best Laptops For Investment Banking
What is a Wi-Fi Antenna?
A wifi antenna helps increase the range of your laptop’s signal observation far beyond your joined wireless card. Since your laptop doesn’t have much space for a long antenna, if the wireless environment becomes too complex because of intervention, extra floors or walls, or being too far away, you may have trouble selecting a good pic. There is a signal.
Step by Step Guide:
Following is the step-by-step guide about how to make a wifi antenna for laptop.
Step 1: Open the soda Can tab. Put soda in the toilet or kitchen sink.
Step 2: Set a sheet of newspaper on a table and place the soda can in the newspaper. Cover your hands by wearing work gloves.
Step 3: Score around the front point of the soda using the utility knife blade. Use scissors to cut the front edge of the soda can when rounding. Throwing away the top cut rim of the soda can result in waste.
Step 4: Insert two drops of dishwashing liquid in a soda can. Fill up soda cans with warm water and wash the cans.
Step 5: Clean the soda can with a paper towel. Throw the paper towel in the trash.
Step 6: Put the soda can in the newspaper. Let it dry completely.
Step 7: Put the soda can in the newspaper on your side, the open side covering the left.
Step 8: Estimate 4 inches of the soda can from the closed end. Use a utility knife to mark a hole at the 4-inch piece. Cut holes with a scissor blade.
Step 9: Bind duct tape across the open rim.
Step 10: Cut off both ends of the coaxial cable by using a scissor. Put a cut of the coaxial cable into the opening within the soda can. Bind duct tape across the coaxial cable to secure it within the spot.
Step 11: Remove the 2-inch strip from the outer arm of the free end of the coaxial cable by using wire strippers and using wire strippers; clear 1 inch of insulation from the end of the central wire.
Step 12: Put the centre wire’s non-insulated head into the centre hole at the back of the wifi plug adapter. Insert inner sheets around the centre wire against contact around the conductor centre wire. Leave the solder to cool for a minute.
Read More: How To Fix Black Spots On Laptop Screen?
Step 13: Wrap the duct tape around the middle wire to link to the wifi plug adapter to cover it from internal shading.
Step 14: Connect the wifi plug adapter into the wifi plug on the laptop.
How to Build a Low-Cost wifi Antenna?
Sometimes, your wifi signal doesn’t get where you want it to go. You’ve spotted wifi adapters on the retailer; however, they are mostly expensive. We’ll show you making a wifi antenna for a laptop using shelf parts, no new software, and without opening your computer case.
Step 1: Get a USB wireless LAN adapter “dongle.”
This little device is about the size of your thumb. It gives wifi capability to your computer. You’ll require it even if your laptop is wirelessly connected.
Get one that has 802.11b and 802.11g standards for best compatibility. For reasonable prices-simple pricing, check out Google, which is essential at close range, costs 15 to 20 USD. The shape is necessary. Find a small thumb-sized device for cost-effectiveness.
Step 2: Take a dish covered with mesh
Asian scoop is used for frying things in cooking utensils. It is easy to use. It is the most useful form and comes with an extended picket deal.
Other choices include sieves, streamers, lamp colors, and pot lids – as long as they are metal and dish-sized. Any parabolic piece of metal mesh will bring a better signal, but it’s harder to carry around.
More costly choices include discarded direct TV pots or umbrellas covered with mesh. Although they should receive more signals, increasing difficulty and wind resistance are approximately 12 inches in diameter. Elastic stalk desk lamps permit them to be neatly installed and positioned.
Step 3: Get a USB passive extension cable.
You have to type A (male) type A (female) cable. This will link the USB wifi adapter to your laptop’s USB port.
The antenna wants its place, so it has a direct line of sight of the wifi entry-level. Make sure your work is long enough to keep the cable in place, up to a maximum of 15 feet. You can link multiple extension cables if required. Dynamic USB expanders permit more cable runs, permitting higher external antenna placement.
Step 4: Target your dish
Find the remote wifi sender you want to access. Your wifi antenna is very directional, so achieving the goal is necessary. The remote antenna is the most effective place to level the dish, although deviating reflections from buildings, etc., sometimes give the right signals from amazing directions. You can use a cheap handheld laser pointer to confirm that your wireless sender is OK.
Step 5: Assemble the system.
Link the USB extension cable and wifi dongle to the dish with tape, die ties, or hot melt glue. You want to dongle at the height of the dish’s centerpiece “hotspot” – radio signals come in and jump toward the centre, just above the surface of the dish. The best dongle location can be found with a simple experiment. One way to do this is to cover the dish with aluminum foil and observe if it reflects the sun. In this case, you will require a small support stick to get the dongle from the dish’s surface. Other methods use wire tied to the dish’s face like a spider’s web, hollow out plastic garden hose equipment, or even cut sticks.
Key features of Wifi Antenna
Signal Type – 802.11 ac is a full 5 GHz and keeps the data streaming more direct on the client’s devices. Older cards and wifi antennas may end up at 802.11n, not giving you the fastest possible data speed.
USB Type – Unless you have an older computer, you should have USB 3.0 ports. It can run at a speed of 5GB per second. If you are using USB 2.0, you are looking for a maximum of 480 megabits per second.
Read More: 10 Best Laptop For Streaming Netflix
Antennas DBI – Antennas fall into DBI, usually for the 2dbi or 5dbi we are looking at. 5dbi antennas are better at weak signals than 2dbi. But 2DBI can maintain strong relations with strong signals.
Conclusion:
Are you looking to make a wifi antenna for a laptop? This article is all for you. In this article, we’ve discussed how to make a wifi antenna for laptop. All the steps are given in detail. You can easily make a wifi antenna by following the above steps. Hope you will enjoy our article. If you have any queries or questions left, feel free to ask. We will try our best to cover your queries and questions. Features are also given in this article for your information. Steps for making low-cost antennas and costly antennas are discussed. Read the article carefully.