Table of Contents
A common problem when repairing and upgrading a laptop is the stripped head. People who have attempted to remove the damage would probably know that it’s tough to loosen despite having the correct-sized screwdriver on hand. You might think of yourself as unlucky or your screwdriver as nothing more than a poor removing tool. However, there are ways to use household items and other parts from broken electronics devices that can help you easily open up laptops, which we’ll be showing you here in this article; we like to work with components from original manufacturers so but we do carry various replacement and upgrade parts for laptops whenever it’s necessary,
Read More: 7 Best Laptop Wireless Card
When your screwdriver can’t handle the task at hand, the best thing to do is to go out and purchase a new one. Otherwise, you risk making worse things happen to either yourself or perhaps the project, so it’s best to be safe rather than sorry! If your screwdriver doesn’t have the right bits, you should use a drill or anything else that will help make removing those stubborn screws much more accessible. Let’s discuss how to remove a Stripped Screw from Laptop.
Using an Elastic Band
Sometimes we need more muscle to get things done! The elasticity of an elastic band is beneficial because it helps hold the screwdriver in place and creates a slippery surface, making it easier for the head of your screwdriver to access tight corners inside once it has been inserted and turned. Any piece of rubber or any elastic band will do; in fact, you can use a rubber band from your wrist or even your sneakers if you want to get creative! Just make sure that it’s stretchy enough; try using a bicycle tire tube or something similar. And always remember to keep the tip (the sharp end) moving at all times so that you don’t strip the hole or break it altogether.
Using the Damaged Screw as the Bit of a Screwdriver
If it is stuck tight and there is a groove in the top of it, you might be able to make use of an extractor. This can be easy because an electrical device can do all the digging without forcing you to use your hands. To make sure this works, place tie with your damaged screwdriver onto what’s left of the stripped head and tighten it up until it makes an imprint before turning it quickly in a counterclockwise motion. If you’re lucky, this method could work because tightening up will have a lot to do with loosening up. Put your machine into reverse mode and slowly give the extractor a try! Go too fast, though, and you might damage the rest of the head. Generally, if this trick works as planned, you should be able to get out any stripped screws by turning them in reverse just like regular screws so long as there aren’t any more denying involved or other problems that may prevent it from working correctly for you. Cross your fingers.
Using a Penetrating Oil Spray
Penetrating oil sprays such as the WD-40 are commonly found at your local hardware store. The magical and practical uses of the WD-40 include its ability to facilitate movement between different rooms in your home. Using this connection, you can hang a painting you purchased at a thrift shop, for example, on the wall supported by said looking glass! The possibilities are endless regarding where and how you can use the penetrating oil. Just make sure you set up everything correctly, making sure that all screws are made of steel, and none of them are part of the motherboard – else this spell won’t work 🙂 To make this happen, first, you’ll want to adequately prepare by giving each a little squirt of WD-40 right where they connect with the motherboard so they’ll be easier to unscrew later on. Then wait a few minutes while they lubricate themselves before trying to disconnect everything from each other.
Using a Dremel:
If the situation requires it, an even more potent variant is to use a slotted. To recreate the slot for the screwdriver on a stripped-down look, you can use a Dremel and cutting disc. The idea is not to blunt the tip but to round up an indentation slightly. First, choose a bur that will fit in your slot (0.5mm max) and then remove a chunk of material so that there is room for the bur to work within it. Ensure that this shaving doesn’t cut too far down into the metal as we want it to return to its original state. You can test if your rounding off has been done right by inserting one end of your slotted screwdriver into the hole and pressing down on the other side with some pressure on it. If there is enough room, then you get a slight indentation, letting you know if there’s still more work needed or not at all.
Using a drill:
If you do not achieve the expected results with one of our previous solutions, it is time to put some muscle into it. Take a piece of paper and create a shield around the hole to protect the motherboard from any shavings generated by drilling. If you have a stainless-steel head, pay particular attention to your drilling speed, or the drill can get damaged quite easily. By using fine pliers, unscrew the remainder of the threaded part and keep the mounting bracket for future use.
Using an Extractor
In today’s manufacturing world, there has been a growing demand for specialized products. These products are created to fulfill the needs of a specific customer or business owner. In that sense, companies need factors outside of traditional drilling to get ahead in the race – and “extractor drills” are just the answer! They are used in the same way as standard drill bits, but their purpose is different; a conventional drill bit would typically penetrate wood or whatever else it was attempting to into – while an extractor drill would extract screws that were already sitting inside.
Read More: How To Boot From Usb Hp Laptop?
However, if you have stainless steel attached to your motherboard, the extractor’s principle is simple but ingenious. As with the elastic method (see above), the guide is to “hang” the head as if it were in perfect condition and unscrew the assembly afterward. With a stainless-steel extractor, this “hanging” principle can be done as quickly as with an elastic band, except that this time there are tiny teeth on one end of the steel device – they act like little claws that grab onto those pesky screws which are so difficult to remove. Then, once the suitable sized extractor has been found, one turns their electric screwdriver in the opposite direction that they would typically turn when attempting to loosen up a bolt.
Rubber band:
A common problem for those unfamiliar with machinery and working on DIY projects is stripped screws. The first thing you should do is turn them to face the right way, to begin with. But if there’s still a problem, try using a rubber band as filler material to fill in gaps left by the turning against itself while also increasing clamping power by five times. Take your rubber band and take it from the middle to the tip of your screwdriver. Place it so that its hug sits snuggly against the side of the shaft of the screwdriver. You won’t be trying to poke a hole through it, but you can still use this one trick to get a bit more grip on your screwdriver handle! What’s great is that you don’t have to do much work – just put it on, and there you go!
Use of extracting Pilers:
Try to find the finest needle nose pliers you can lay your hands on to get a hold of them. Ideally, some part of the head should be exposed so that you can get a grip on it to turn counterclockwise (left). Sometimes, gaining a hold by inserting one nose into the slot where the screwdriver goes typically is sufficient enough. Use a light grip with the pliers when removing these tiny screws because they are delicate, as we already mentioned, and cannot handle as much pressure as their bigger counterparts used in building wooden furniture or something along those lines. Remember this: if you feel like there is too much resistance, stop immediately since the structure will most likely fall apart entirely if you keep applying excessive force. These tiny screws should not stand between you and your most excellent computer hack idea by using finesse and enough patience!
Super Glue:
Finally, if you don’t have a Phillips head screwdriver and can’t find anything else to use, you could try using super glue (like the Araldite or Gorilla brand) or epoxy instead. Super glue generally only gives you a few minutes to get the object in place, so do it as quickly as possible. For example, if your laptop is broken into either a laptop bag or its case, try sticking something somewhere near where the screws are that might work – say, an eraser end from one of your highlighters, a pebble from outside, or whatever else you may have on hand. You can also use rubber cement to put something flat against the hole to put some grip back on it.
Read More: 10 Best Laptop For Car Tuning
Conclusion:
Often in life, when you take out a which has already been screwed into something else, you should replace it with another new one in its place. If you don’t, your project could be at risk of coming undone and falling apart. What good is a bicycle chain if you don’t have any bikes? Once it gets taken out, make sure to replace it with a brand new one to protect your investment.
Fixing something yourself can be extremely tough if you’ve never done it before, and so we hope this guide has given you the confidence to work on repairing things around the house for yourself. Finally, it’s all about how to remove a Stripped Screw from Laptop.
Read More:
How To Turn On Keyboard Light Windows 10?
10 Best Laptops For Screenwriters,